How to build a center console

Building a custom console is relatively easy to do, but if you try hacksawing metal or plumbing metal parts together you might end up with something that looks more like a Jackson Pollock painting than something that could be found in a Ferrari. That’s because building a center console requires both art and science, something that can be challenging for an artist or a scientist to know how to do.

A center console is a piece of furniture that can be found in a vehicle—it’s a shallow box, or compartment, built into the center of the car.

How to build a center console

Building a center console for your truck can be a fun project, especially if you are making it for a specific application. If you want to make one for yourself, here is how to do it:

1. Choose your materials

2. Cut out the pieces

3. Assemble the pieces

4. Install the center console in your vehicle

This is a guide on how to build a center console for your truck. It will show you how to build it using the most basic tools and materials, so even if you don’t have access to fancy equipment, you can still make one.

Step One: Cut the Wood

The first thing you’re going to need to do is cut the wood into pieces that will fit in your truck bed. The main piece should be large enough that it can hold all of your stuff, but small enough that it doesn’t take up too much space in the bed of your truck. You’ll also need several smaller pieces cut out to make sure everything fits together properly.

Step Two: Drill Holes

Once everything is cut out, drill holes into each piece so that they all line up properly when assembled together. You’ll want these holes as close as possible to where they’ll be screwed in place, since this makes drilling easier and prevents splintering around the screw heads later on down the road.

Step Three: Attach Pieces TogetherHow to build a RV Center Console - Sidetracked by Adventure

Now it’s time to assemble your center console! Start by attaching two small pieces at opposite ends of one long piece using screws or nails (don’t use glue yet!) Once those are attached, repeat

The center console is an important part of your truck. It’s where you keep things like loose change, sunglasses, and other items that you need close at hand. It’s also a great place to store CDs, maps and other items you need while traveling.

If you don’t like the stock look of your center console, it’s easy to build one yourself. These instructions will show you how to build a custom center console for your truck in just a few hours.

Materials Needed:

1/8-inch plywood

Wood glue or construction adhesive


Paint or stain (optional)

Center consoles are a great way to add storage and organization to your vehicle. They can be as simple as a small box in the middle of the floor, or they can be complex systems that offer cupholders, USB ports, and even laptop chargers.

Building a 22' Center Console Carolina-style boat

The basic idea behind center consoles is simple: You’ll need a box that fits between the seats and provides an accessible space for storing small items. Some people prefer to build their own custom center console from scratch, while others choose to buy pre-made products from retailers like Amazon or eBay.

This guide will show you how to build your own cheap center console for under $100, but if you’re looking for something more sophisticated, check out our article on building an Xbox One X luggable gaming PC into a car’s center console — it’s a lot more work than this guide but it gives you much more freedom for customization.

This is a guide that will help you build a custom center console for your truck. The main goal of this project is to make your truck more comfortable, while keeping it looking good.

This article was written with the assumption that you have some basic knowledge of woodworking and/or metal working. If not, I would recommend taking some classes or reading up on the subject before attempting this project.

Materials:CSC Motors: Building A Custom Center Console

– Piece of solid wood (1×3 or 1×4) (mine was 1×3) – $3-4 at Home Depot or Lowes

– Piece of MDF (medium density fiberboard) – $5-6 at Home Depot or Lowes

– Spray paint (color of your choice) – $5 at Walmart or Target


– Drill press (or hand drill) – $15 at Harbor Freight Tools, if you don’t already own one

– Router table (optional) – Not required but highly recommended. You can get one used for around $100 on Craigslist or eBay

When it comes to building a custom center console, you have a few different options. You can buy a pre-made console that is designed specifically for your make and model of truck, but this can get expensive. Luckily, there are other ways to build a custom center console for your truck.

Here’s how to build a custom center console for your truck:

Measure the space in your truck bed where the console will go. You want to make sure that it will fit in there before moving forward with any other steps.

Buy or find some wood that is the same width as your truck bed. Cut it into four pieces so that it will fit into the space at an angle like this:

You should be able to use these pieces of wood as both sides of the console and as support beams for other parts later on in this project. Also, make sure each piece is long enough so that they can reach from one side of the bed all the way to the other side without being cut down any further or having additional supports added later on in this project!

The center console is a perfect place to add storage, but if you don’t want to spend a lot of money, you can build one yourself. The first step is to find the right materials.

Start with an inexpensive piece of plywood that’s at least 3/4 inch thick. When you’re looking for your plywood, keep in mind that some stores sell different types of plywood: regular and waterproof (marine). The marine variety will be more expensive but it’s better suited for this application because it won’t absorb water from rain or snow like regular plywood does. You’ll also need a few other supplies like screws, glue and paint.

Once you’ve gathered all your materials, start by laying out your design on paper and marking where each hole should go. Then transfer that design onto the wood using pencil so you know exactly where everything goes before drilling holes in your project. Once everything’s marked out, start screwing in screws every few inches along the bottom of your center console so it can rest on top of the front seats without falling off if someone leans against it while driving down the road. When that’s done, cover up all your holes with wood filler so they won’t show through after painting

The Center console is the best way to make your truck more comfortable and functional. Center consoles come in all shapes and sizes, and they can be installed on any type of vehicle.

Here are some tips on how to build a custom center console for your truck:

1. Measure the distance between the seat and steering wheel. You want to make sure there is enough room for the console to fit into this space comfortably. If not, you can always adjust it later by cutting off a few inches from one side or the other.

2. Use wood glue or another adhesive to attach two 1x4s together so that they form an L-shape (if you are using plywood). Make sure that they are flush with each other at both ends before applying any glue so that they line up perfectly when joined together in step 3 below.

3. Attach one end of your 1x4s onto your seat using screws (or another method if using plywood). Make sure that the boards are flush and even with each other along their full length so that when you attach them together later they will be flush with each other at both ends without needing any adjustment whatsoever). Then attach the other end of each board onto either side of

If you’re looking for a way to add storage and style to your truck, the Center Console Insert is the perfect solution. This center console installs easily into any Ford F-150 or Super Duty crew cab that has a center console, and it can be customized with custom upholstery fabrics.

The Center Console Insert features:

A large storage area for storing loose items such as cell phones, sunglasses, spare keys and more.

A cup holder for holding drinks or small items like pens.

A removable tray with a locking lid that can be used for small electronics such as smartphones or tablets.

The more you work with woodworking and metalworking, the more you’ll realize there are many different ways to tackle a project.

As a woodworker, I’ve taken on many different projects for friends and family members — everything from bathroom vanities and kitchen cabinets to entertainment centers.

When it comes to building something for yourself, it’s important to take into consideration what you want out of the project. If it’s just for fun or something small, then by all means get creative. But if you’re doing this so that your truck has more storage space or other functional uses, then consider using these tips:

1) Measure twice, cut once

2) Use as few clamps as possible

3) Use screws rather than nails whenever possible

Leave a Reply

Your email address will not be published. Required fields are marked *