There are several different ways of constructing a 40 antenna tower. It is important to create the best base for the tower. If you want to be able to pick up all available TV stations, your foundation has to be squared and level with the ground.
Building your own antenna mast can be a fun and rewarding experience. An antenna mast is used to support an antenna for the purpose of sending and receiving cellular signals: voice, data, SMS, GPS, etc. Using your cell phone won’t be any different from using it before you build a mast. However, when you build a 40-foot mast and install it outside, you will find that your cell reception has greatly improved. Your cell phone call quality will sound almost identical to that of a landline phone call with no outside interference.
![Anyone ever installed a free standing 40 foot tv tower before? Any advice? : r/amateurradio](https://i.pinimg.com/originals/97/f0/22/97f02235eff258f2916e69f7f5e99a38.jpg)
How to build a 40 antenna mast
Buy the antenna mast and antenna mount that will work with your CB radio. If you’re using a handheld radio, look for a push up antenna pole. These are available in lengths of 16, 24, 30 and 40 feet. If you have an in-vehicle CB radio, you’ll need to purchase an exterior mount and an extension cable to connect it to your dash.
The size of your vehicle will determine how tall your antenna should be. A 40-foot antenna is typically used on large trucks and buses, while a 30-footer works well for cars and SUVs that have plenty of room on their roofs.
The next step is to build your own antenna mast.
In this article, we will discuss how to build a 40-foot antenna mast. This is a great height for most applications and will give you the best chance of getting your signal out.
The first thing you need to do is cut the top section off of your antenna pole. This will leave you with just enough metal to attach your antennas to (see image below). You can use any tool or saw that you have available; however, if you have access to a chop saw, it will make this process much easier and quicker.
Next, drill holes in each end of your pipe cap and bolt it onto the end of your antenna pole. You want these bolts to be tight as they will hold everything together while also protecting them from corrosion over time. The more torque you apply while tightening these bolts down, the better!
After attaching the cap, cut off two 6-inch sections of coax cable and strip off about 1/4 inch of insulation from each end using wire strippers or scissors (see image below). These two wires will be connected directly to our cb radio’s ground post on its mounting bracket next so that we can transmit our signal through them when we are done installing everything
The first thing you need is an antenna mast. It can be made of steel rebar, wooden 2x4s or PVC pipe. Make sure it’s strong enough to support your antenna and the weight of the coax cable running down it.
Next, you’ll need some guy wires. These are ropes that go from the top of your antenna mast to the ground to provide stability in high winds and keep it from falling over.
Finally, you’ll need an antenna mount, which will sit on top of your roof or deck railing and hold up your CB radio.
![Build a 40' Antenna Mast at Home [DIY Guide]](https://www.savenetradio.org/wp-content/uploads/DIY-Guide-to-Build-a-40-Antenna-Mast-800x600.webp)
Here’s how to build a 40-foot antenna mast:
1. Get an antenna mast pole.
2. Cut the pipe to the right length.
3. Bend the pipe into the right shape (see diagram).
4. Drill a hole through each end of the pipe, and screw in a bolt from inside the pipe. Tighten with a wrench or ratchet to make sure that it is secure. You might want to use lock nuts on one side, so that you can remove them later for maintenance or repair work.
A 40-foot mast is a great choice for an antenna. It’s tall enough to get above most obstacles, and it’s not too difficult to build. Here’s how you can build your own 40-foot mast in a few simple steps.
1. Find a location for your antenna that gets good signal strength. If your home has a garage or other outbuilding, it might be a good place for the mast. Make sure the area is level and well-drained — if there is standing water in the ground around where you’ll be building, it could cause problems with your antenna later on.
2. Decide on how high above the ground you want your antenna to be, then use this formula:
Height = (Frequency x Velocity Factor) + Antenna Length + 15 Feet
For example, if you want an antenna at 30Mhz (10 Meters), then plug those numbers into the formula:
Height = (30 x 2) + 36″ + 15′ = 94″ or 7’11”
30 Foot Antenna Pole
The 30 foot antenna pole is a great choice for CB radio users who want to mount their antenna higher than the standard 17 feet. This antenna pole is the same diameter as the 17 foot pole but it is about 3 feet longer. This allows you to mount your CB radio higher on your house or RV, which may improve your signal strength and reception.
![Build a 25'-50' free standing Tilt then Crank up tower antenna](http://qrznow.com/wp-content/uploads/2016/02/s-l16001.jpg)
Antenna Mast Pipe
The cb antenna mast pipe can be used with any type of cb radio antenna. The cb antenna mast pipe comes in various sizes and lengths, including 12 inches and 36 inches. The cb antenna mast pipe is also made from aluminum so it won’t rust or corrode over time like some older pipes do.
Push Up Antenna Mast
The push up antenna mast is an ideal solution if you are looking for an easy way to raise your CB radio antenna without having to use a ladder or climb up on your roof every time you want to adjust it or make repairs. It’s also great if you don’t have any room on your property for a tower or antenna tower pipe because it just sits on top of the roof instead of taking up valuable ground space!
We offer the best quality cb antenna mast pipe at affordable prices. All of our products are made from high-quality materials and we offer a wide range of colors, sizes, and styles for you to choose from. Our products are also durable, long-lasting and easy to install. We ship our products worldwide to guarantee that you will get them on time.
CB Antenna Mast Pipe
Our push up antenna mast pipe comes in a variety of colors and sizes. We also offer custom designs if you want something other than what we have in stock. The push up antenna mast pipe is made with high-quality materials that are durable enough to last for years without any problems at all. The push up antenna mast pipe is easy to install since it only needs one person to get it installed correctly. You can easily use this product in your home or business if you want to improve the visual appeal of your property.
![Build a 25'-50' free standing Tilt then Crank up tower antenna](http://qrznow.com/wp-content/uploads/2016/02/s-l1600-1.jpg)
Antenna mast pipe is suitable for all kinds of CB, FM and TV antennas. It can be cut to the desired length according to your need.
The antenna mast pipe comes with a 3/4″ threaded adaptor at the bottom, which allows it to be mounted on a tripod or any other mounting device. The top end of the antenna mast pipe has an adjustable spring loaded push up mechanism that allows you to raise or lower your antenna without having to use any tools.
The push up antenna mast is made out of high quality aluminum material and is designed for light-duty use only. This antenna mast can support up to 30 pounds of weight at maximum height, which makes it perfect for most mobile applications such as boats, trucks, vans and more!
The CB Antenna Mast is a great tool for mounting your antenna. The antenna mast is made of steel and can be used for any CB radio. The CB Antenna Mast comes with a tilt feature, allowing you to adjust the antenna so that it points in the direction you want. This push up antenna mast has an adjustable height range of 24” to 36” which should be enough for most people.
The CB Antenna Mast is easy to use, just push up into the ground and tighten down with two wing nuts on top of the pole. The CB Antenna Mast is also very lightweight at only 8 lbs., making it easy to move around or take down if needed.
The Push Up CB Antenna Mast includes:
1x Push Up CB Antenna Mast
2x Wing Nuts
Push-up antenna masts are made of fiberglass, which makes them lightweight, strong and durable. The fiberglass is also resistant to corrosion, which allows it to withstand the elements.
Push-up antenna masts can be used in any weather conditions without fear of damage. They are easy to assemble and disassemble with no tools required.
The mast comes with a heavy duty mounting bracket that fits any vehicle and will not scratch the paint when installed properly.
The push up antenna mast is about 3 feet tall when pushed down for storage and extends up to 30 feet high when extended.